Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

This is the place where the type of fluid/material is defined together with its properties.

 

 

RealFlow Scene

In RealFlow | Cinema 4D it is possible to use multiple "Scene" trees in the same project:

  • To link the "Fluid" node to a different scene tree dragging the appropriate "Scene" node to this field 
  • Furthermore you have direct access to the selected "Scene" tree's → "Solver", → "Cache", and → "Display" tabs. For descriptions of these parameters follow the links.
  • Quick access to the "Solver" settings comes in handy when you work with Dyverso materials (granular, viscous, viscoelastic, rigid, elastic).

RealFlow | Cinema 4D supports interactions between different "Fluid" domains, e.g. for the creation of foam or water-and-oil simulations. To link the fluids drag one or more "Fluid" node(s) to this field.

Type

There are six different types of fluids and materials - and they are able to interact. All types, except "Dumb", are GPU-accelerated:

  • "Dumb” particles are often used for spray or foam. These particles cannot react with each other and do not have the characteristic fluid properties, but they are simulated very fast.
  • "Liquid - SPH" is a very accurate fluid solver.
  • "Liquid - PBD" is a very fast fluid type (faster than “Liquid - SPH”).
  • "Granular" is suitable for substances like sand or snow.
  • "Viscous" fluids are suited for substances like caramel, yogurt, oil, or lava.
  • "Viscoelastic" is the choice of materials such as rubber, caoutchouc, silicone, or "memory foam".
Resolution

With this setting you can change the amount of particles, “Resolution” mainly depends on scene scale and emitter scale, but it also affects the fluid’s mass and therefore depends on “Density”, too:

  • With “Resolution” set to 1.0, a volume of 1 m x 1 m x 1 m filled with 1,000 particles.
  • The parameter accepts any positive value.
Density

This parameter is defined as mass per volume unit and is different for each substance. “Density” does not change the fluid's behaviour, but it is possible to mix fluids from different domains. This way you are able to simulate substances like oil and water. The unit is kilograms per cubic metre. The density of water is 1,000 kg/m3. Avoid very small values close to 0, because they can lead to instabilities.

Internal pressure

“Internal Pressure” simulates the forces between nearby particles and pushes them apart - this makes the fluid fill a greater volume. This parameter accepts any positive value ≥ 0.

External pressure

“External Pressure" tries to limit a fluid’s expansion tendency and can be compared to atmospheric pressure. Particles tend to "stick" together with higher values. This parameter accepts any positive value ≥ 0.

Surface tension

A fluid's tendency to contract and create drops and tendrils is increased with higher settings. You can enter any positive value ≥ 0. The substeps settings in RealFlow | Cinema 4D's → "Solver" tab influence how this parameter acts on the fluid.

Vorticity boost

To get a more turbulent and water-like fluid, increase this factor, but try to avoid very high values (unless necessary), because they can completely distort the fluid. In many cases, values between 1.0 and 50.0 produce good results, but there is no limit.

Viscosity

Substances with very high viscosity are honey, tar or syrup, for example. Fluids with low viscosity are alcohol, many solvents or liquid gases. The default value of 3.0 describes the viscosity of water. You can enter any positive value and 0.

Max particles

Please enter a value to stop emission at a certain amount of particles. "Max particles" is based on the total amount of emitted particles. Let's say you have entered "50,000". If there are currently 1,000 particles in your scene, but you have already deleted 49,000 particles RealFlow will stop the emission.

Use Initial State

Initial states can be created and activated/deactivated individually for each "Fluid" node (also see → "Initial States"). When

  • enabled the initial state will be used
  • disabled the initial state will be deactivated temporarily.
Create Initial State

This function lets you set any simulation frame as a new start preset. When you reset the scene the simulation will be starting from the previously defined initial state. The associated initial state file will be written to the scene's catch folder specified under Scene > Cache. Here is the workflow:

  • Simulate (click on the timeline's "Play" button)
  • Stop the simulation at any time and press "Create Initial State.
  • Set “Use Initial State” to “Yes” if necessary.
  • Rewind the timeline to frame 0; the initial state is shown.
  • Simulate.
  • No labels